BLOG

MY PERSONAL JOURNEY

DG201ABK DATASHEET PDF

DGABK datasheet, DGABK pdf, DGABK data sheet, datasheet, data sheet, pdf, Intersil, Quad SPST, CMOS Analog Switches. DGABK Datasheet, DGABK PDF, DGABK Data sheet, DGABK manual, DGABK pdf, DGABK, datenblatt, Electronics DGABK. DGABK datasheet, DGABK circuit, DGABK data sheet: MAXIM – Quad SPST CMOS Analog Switches,alldatasheet, datasheet, Datasheet search site.

Author: Fenrikree Mulkree
Country: Guadeloupe
Language: English (Spanish)
Genre: Career
Published (Last): 24 June 2009
Pages: 76
PDF File Size: 18.11 Mb
ePub File Size: 20.19 Mb
ISBN: 845-3-18714-674-1
Downloads: 80925
Price: Free* [*Free Regsitration Required]
Uploader: Gubei

In the OFF state each channel blocks voltages up to the supply rails. Device mounted with all leads soldered to PC board.

This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Package Information continued The package drawing s in this data sheet may not reflect the most current specifications. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. D, D1, and E1 dimensions do not include mold flash or protrusions. Documents Flashcards Grammar checker.

Dambar protrusions shall not exceed 0. E and eA are measured with the leads constrained to be perpendicular to datum -C. The DGA has a maximum turn-off time of ns and a maximum turn-on time of ns.

All Rights Reserved All other trademarks mentioned are the property of their respective owners. The DG has a maximum turn-off time of ns and a maximum turn-on time of ns. For information regarding Intersil Corporation and its products, see www.

Maxim reserves the right to change the circuitry and specifications without notice at any time. For more information on TYP values see Note 3. This dimension allows for off-center lid, meniscus, and glass overrun. For this configuration dimension b3 replaces dimension b2. VO is the steady state output with switch on. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. Measure dimension S1 at all four corners.

  ISTQB DOROTHY GRAHAM PDF

However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use.

These are stress ratings only, and functional operation of the device at these or any other conditions eatasheet those indicated in the operational sections of the specifications is not implied. For more information on TYP values see Note 2. Pin Configurations continued To provide protection for overvoltages up to 20V above the supplies, a 1N or 1N type diode should be placed in series with datasheef positive and negative supplies as shown in Figure 2.

B1 maximum dimensions do not include dambar protrusions.

DGABK (MAXIM) – Quad SPST CMOS Analog Switches

Typical values are for design aid only, not guaranteed and not subject to production testing. SR Datasheet – Micropower Dataaheet. Maxim guarantees that these switches will not latch up if the power supplies are disconnected with input signals still connected. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied.

These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. When the enable input is high, a channel is selected by the address inputs, and when low, all channels are off. A notch or a pin one identification mark shall be located dataaheet to pin one and shall be located within the xatasheet area shown. N is the maximum number of terminal positions.

  HALDIGHATI POEM PDF

Dimensions b1 and c1 apply to lead base metal only. The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet.

In either case, source-to-body diodes can be forward adtasheet and conduct current from the datashete source. Dimension Q shall be measured from the seating plane to the base plane. An enable input is provided. Lab 6 in this note. Putere n-am, Tu-mi fii sprijin. Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product.

Limit diode current to maximum current ratings. Asa cum sunt, la Tine vin! The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply.

Copyright Intersil Americas Inc. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

DG211 Datasheet PDF

Dimension M applies to lead plating and finish thickness. Parameter guaranteed by design or dayasheet. Information furnished by Intersil is believed to be accurate and reliable.

Feedthrough via gate capacitance may result in spikes at leading and trailing edge of output waveform. In case of conflict between English and Metric dimensions, the inch dimensions control.

Mold flash or protrusions shall not exceed 0. For the latest package outline information, go to www.